The C.N.R. Project

The Chung's Negative Resistance experiment

Created on 05-20-01 - JLN Labs - Last update 06-19-01
All informations in this page are published free and are intended for private/educational purposes and not for commercial applications


<< In a July 9, 1998, at the 5th International Conference on Composites Engineering in Las Vegas, Dr. Deborah D. L. Chung, professor of mechanical and aerospace engineering at University at Buffalo (UB), reported that she had observed apparent negative resistance in interfaces between layers of carbon fibers in a composite material. Professor Chung holds the Niagara Mohawk Chair in Materials Research at UB and is internationally recognized for her work in smart materials and carbon composites. The negative resistance was observed in a direction perpendicular to the fiber layers. A paper describing the research was submitted by Chung to a peer-reviewed journal, and a patent application was filed by the University. >> Document source "On Extracting Electromagnetic Energy from the Vacuum," IC-2000, by Tom Bearden

Now, On May 19th, 2001, I have been able to replicate successfully the Chung's Negative Resistance (CNR). You will find in these pages all informations and datas about the CNR experiment that I have done. The CNR experiment has been conducted so as to be closer to the original Chung's design which is fully described in the paper "Apparent negative electrical resistance in carbon fiber composites," by Shoukai Wang and D.D.L. Chung - Composites, Part B, Vol. 30, 1999, p. 579-590.

A) - Brief description of the CNR experiment conducted by D. Chung and S. Wang in 1998

The original CNR design consisted in two 6 mm strips of 7 micrometer unidirectional carbon fiber which have been previously pressed ( at 1.4 MPa ) together and glued with epoxy cement in a crossply configuration to form a 6x6 mm junction.

In the CNR diagram above, the top lamina is AB and the bottom lamina is CD. The voltage difference between the two laminas in the junction has been measured across B and C and the current flows from A to C with a standard resistor ( R1 ) connected in serie. A Keithley 2001 multimeter has been used during this experiment. The electrical current was calculated by Ohm's Law ( I = U(R1) / R1 ).

An apparent negative resistance has been measured at the junction : the current-voltage characterictic was a straight line with a negative slope through the origin. The electrons, in the junction, seemed to travel in the unexpected direction ( backflow ) according to the voltage gradient.

For more informations and technical datas read : "Apparent negative electrical resistance in carbon fiber composites," by Shoukai Wang and D.D.L. Chung - Composites, Part B, Vol. 30, 1999, p. 579-590.

B) - The JL Naudin's Negative Resistance experiment replication done on May 19th, 2001

I have used a Tektronix Function Generator AFG-310. The point A has been connected to its positive output and the point E to its ground. The signal output has a triangular shape, a frequency of 0.1 Hz and 10 Volt Peak. The voltage measurements have been done with a Tektronix oscilloscope THS720 which has ground isolated channels. ( see the testing setup diagram below )

CNR v1.0 : TESTS

The first CNR v1.0 device has been built according to the description done in the Dr Chung's paper cited above. I have used two similar strips of carbon fiber (see the photo below ) glued with epoxy in a cross shape.

CNR v1.0 : tests results :

The slope of the Current-Voltage curve was POSITIVE and thus the measured resistance junction was POSITIVE. The measured current changed from -60mA to +60mA and the measured voltage across the CNR junction changed from -40mV to +40mV at a rate of 0.1 Hz.

The measured junction resistance between the carbon fiber strips was +0.667 ohms

Interesting notes : I have noticed that if I increase strongly the pressure of the carbon layers at the junction, I have been able to change the slope of the the current-voltage curve. I have been able to nullify the slope ( the junction resistance = zero Ohm ) and also to get a negative slope ( the junction resistance < 0 ). This has encouraged me to continue the investigation, and thus I have decided to build a new CNR device with a stronger junction pressure during the gluing phase...

CNR v2.0 : TESTS

The first CNR v2.0 device has been built with the same method than the v1.0, but the junction pressure has been strongly increased comparing to the previous version during the gluing phase with the epoxy cement (see the photo below ).

( Above ) Photo of the testing setup

(Above) A detailled view of the CNR v2.0 under test, the orange line shows the current path

The red curve shows the voltage measured across CNR junction
The blue curve shows the voltage measured across Resistor ( R1=98.7 ohms ).

CNR v2.0 : tests results :

The slope of the Current-Voltage curve was NEGATIVE and thus the measured resistance junction was NEGATIVE. The measured current changed from -64mA to +64mA and the measured voltage across the CNR junction changed from -14mV to +14mV at a rate of 0.1 Hz.

The measured junction resistance between the carbon fiber strips was -0.218 ohm

The negative resistance of the CNR junction has also been measured in DC

The results are now very encouraging, today, I can confirm experimentaly the "Negative Resistance" discovered by Dr. Chung in 1998.

It is interesting to know that Dr Chung and Wang have demonstrated negative resistance as low as -8 ohms for a contact area of one square centimetre.

The CNR is an "apparent" Negative resistance rather than a true resistance. Its mechanism seems equivalent to a true negative resistance because the electrons flow in the unexpected direction relative to the applied current/voltage and this occurs only in the junction between the two carbon fiber laminas,  the XY section showed in my 3D diagram. The equivalent model of the CNR can be easily simulated by a computer ( see the CNR simulation ) and the interesting fact to observe is that a negative value for the Rneg must be set for getting the same result than the working unit.

In the CNR experiment presented here, the most important fact is that we have a solid state and a static device where we can observe easily an electron backflow in its junction.

Dr Chung has said in his paper (1) : << The control of the relative amounts of the backflow and forward flow means the control of the total apparent resistance. In the situation of zero apparent resistance, the two flows are nonzero but balanced, such that the voltage across the flow region is zero. The current loops in this region suggest the possibility of interesting and electromagnetic effects.
...
The mechanism of apparent negative resistance is quite rich, due to the involvement of electron backflow. >>

Today, my primary objective ( a close replication of the Chung's experiment done in 1998 ) is now reached. Now, I need to think and focus on the understanding of this very interesting phenomenon.

I shall keep you informed about my progress in this field of research through this web page : http://jnaudin.free.fr/cnr/.

Thanks you very much to all for your encouragements and your helpful support.

Best Regards
Jean-Louis Naudin
Email: JNaudin509@aol.com
Web site : http://go.to/jlnlabs/


Documents references and Press releases :

  1. "Apparent negative electrical resistance in carbon fiber composites," by Shoukai Wang and D.D.L. Chung - Composites, Part B, Vol. 30, 1999, p. 579-590.
  2. Research Focusing On Mechanism Behind Observation of Negative Electrical Resistance by Ellen Goldbaum ( UB )
  3. "On Extracting Electromagnetic Energy from the Vacuum," IC-2000, by Tom Bearden
  4. Astonishing Breakthrough - New Electronics Industry Born - Sighting
  5. Buffalo's MAE Annual report ( 1998 )
  6. 'Negative resistance' surprises material scientists by PhysicWeb News
  7. Dr. Deborah Chung's Negative Resistor by Tom Bearden
  8. UB Scientist Discovers Carbon Composite is a Semiconductor
  9. Holy Grail of electricity claimed by Human Interest Headlines
  10. Drift-diffusion balance explains `negative resistance' of material by Nadya Anscombe ( Electronics Times )

Patents :

Carbon Fibers :


For more informations, please contact : JNaudin509@aol.com


Return to the CNR home page